Question 8.9: SAE 10 oil is flowing through a pipe line at a velocity of 1...

Introduction to Fluid Mechanics and Fluid Machines

SAE 10 oil is flowing through a pipe line at a velocity of 1.0 m/s. The pipe is 45 m long and has a diameter of 150 mm. Find the head loss due to friction. [ρ = 869 kg/ $m^{3}$ and μ = 0.0814 kg/m . s]

The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

Related Answered Questions

Question: 8.15

For the following thrust bearing (Fig. 8.21), show that the force on the straight slider in the x-direction is the same as that on the guide. ...

Verified Answer:

It is given that the velocity profile is [l...

Question: 8.13

A slipper (slider) and plate (guide), both 0.5 m wide constitutes a bearing as shown in Fig. 8.19. Density of the fluid, ρ = 9.00 kg/m³‚ and viscosity, μ = 0.1 Ns/m². ...

Verified Answer:

(a) Considering the width as b and using Eq. (8.70...

Question: 8.12

A circular pipe of radius a and length L is attached to a smoothly rounded outlet of a liquid reservoir by means of flanges and bolts as shown in Fig. 8.18. At the flange section the velocity is uniform over the cross-section with magnitude V0. At the outlet, which discharges into the atmosphere, ...

Verified Answer:

For the control volume as shown, continuity equati...

Question: 8.11

A wind tunnel has a wooden (ε = 0.0001 m) rectangular section 40 cm by 1 m by 50 m long. The average velocity is 45 m/s for air at sea-level standard conditions. Find the power required if the fan has 65 percent efficiency. For air, ρ = 1.2 kg/m³, μ = 1.81 × 10^-5 kg/m-s. ...

Verified Answer:

The wetted perimeter of the duct is

...

Question: 8.10

Heavy fuel oil flows from A to B through a 100 m horizontal steel pipe of 150 mm diameter. The pressure at A is 1.08 MPa and at B is 0.95 MPa. The kinematic viscosity is 412.5 × 10^-6 m²/s, and the relative density of the oil is 0.918. What is the flow rate in m³/s? ...

Verified Answer:

The Bernoulli′s equation between A and B [l...

Question: 8.8

The velocity distribution for a fully-developed laminar flow in a pipe is given by u = – R²/4μ.∂p/∂z[1-(r/R)²] Determine the radial distance from the pipe axis at which the velocity equals the average velocity. ...

Verified Answer:

For a fully-developed laminar flow in a pipe, we c...

Question: 8.7

In the laminar flow of a fluid in a circular pipe, the velocity profile is exactly a parabola. The rate of discharge is then represented by volume of a paraboloid. Prove that for this case the ratio of the maximum velocity to mean velocity is 2. ...

Verified Answer:

See Fig. 8.17. For a paraboloid,

v_{...

Question: 8.6

The analysis of a fully developed laminar flow through a pipe can alternatively be derived from control volume approach. Derive the expression vz = R²/4μ [-dp/dz] ]1-r²/R²] starting from the control volume approach. ...

Verified Answer:

Let us have a look at Fig. 8.17. The fluid moves d...

Question: 8.5

Water at 20 ºC is flowing between a two dimensional channel in which the top and bottom walls are 1.5 mm apart. If the average velocity is 2 m/s, find out (a) the maximum velocity, (b) the pressure drop, (c) the wall shearing stress, and (d) the friction coefficient [m = 0.00101 kg/m . s]. ...

Verified Answer:

(a) The maximum velocity is given by [latex...

Question: 8.4

Water enters a rectangular duct at a rate of 10 m³/s as shown below. Two of the faces of the duct are porous. On the upper face, water is added at a rate shown by the parabolic curve, while on the front face water leaves at a rate determined linearly by the distance from the end. The maximum values ...

Verified Answer:

Consider the top surface. The water enters the top...