Holooly Plus Logo
Holooly Plus Logo

Question 2.23: PSpice Example Use PSpice to find the current, I, in the cir...

PSpice Example

Use PSpice to find the current, I, in the circuit of Example 2.12 (shown in Figure 2.82).

2.23
The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

Follow the steps in the PSpice tutorial to set up the PSpice circuit for Example 2.12 , shown in Figure 2.82 . The PSpice schematic solution is shown in Figure 2.83 .

Next, set the simulation type to be “Bias Point” and run the simulation. The PSpice result is shown in Figure 2.84 .

2.23-

Related Answered Questions

Question: 2.25

PSpice Example Use PSpice to calculate the dissipated power in Example 2.16 (see Figure 2.88). ...

Verified Answer:

You have already learned how to set up the PSpice ...
Question: 2.24

Electric Shock Consider the unfortunate bald utility worker of Example 2.13 who climbs an aluminum ladder with bare feet and comes into contact with an overhead power line bearing 30 cos(100 πt) Kv (Figure 2.86). The worker’s body resistance is 315 kΩ. This situation can be modeled as a resistor ...

Verified Answer:

First, given the voltage source of 30 cos(100 πt) ...
Question: 2.22

Dependent Source Determine the voltage, VA, across the 50-Ω resistor in Figure 2.58. ...

Verified Answer:

V_2 is the voltage that corresponds...
Question: 2.21

Dependent Source Find the current, Ix, that is shown in Figure 2.57. ...

Verified Answer:

Here, the current direction is arbitrarily selecte...
Question: 2.20

Door Opener A driveway gate shown in Figure 2.48 is driven by an electric motor that is connected to a voltage source of 200 V. In order to move the driveway gate, a force of 500 N or more is required. Assume that the motor drives the driveway gate at a constant speed of 0.2 ms^−1 and that the gate ...

Verified Answer:

Here, force, F = 500 N, velocity, V_e = 0.2...
Question: 2.19

Power Dissipation Figure 2.47 represents a circuit that includes a dependent current source as detailed in Section 2.9. Here, the current of the current source is a function of the current in the 3 kΩ resistor. How much power is dissipated in the 33 kΩ resistor in Figure 2.47? ...

Verified Answer:

The current source generates a current in the 33 k...
Question: 2.17

Robotic Arm A robotic arm—5 m long—is designed to load containers onto a cargo ship (Figure 2.45). The maximum mass that can be lifted by the robotic arm is 500 kg at a constant angular velocity of 0.2 rad/s. The power required to initiate the lifting is five times the power required for the ...

Verified Answer:

The torque required to lift up a 500 kg container ...
Question: 2.16

Voltage Direction Versus Current Direction Assuming the directions of current and the polarities of voltages shown in Figure 2.44 refer to the true (positive) values, do the following voltage/current labels conform to how passive elements should be referenced? ...

Verified Answer:

In passive elements, the current enters the positi...
Question: 2.15

Computing Resistance Water conducts electricity. Electricity and water can be a fatal combination, as will be detailed in later chapters. As is also the case with other conductors, water resists the flow of electric current. Pure water has a resistivity of ρ = 182 kΩ-m. However, most water has some ...

Verified Answer:

Using Equation (2.11), we know that: R =\rh...
Question: 2.14

Length of Tissue Suppose that surgeons remove a cylindrical-shaped piece of tissue of unknown length from a patient. Their measurement for a piece of tissue shows that ρ = 250 Ωm and the cross section is 6.875 × 10^−9 m². When a voltage of 30 V is applied across the entire length of the tissue, the ...

Verified Answer:

Assume R is the resistance of the tissue. Using Oh...