Question 2.14: A horizontal force 1 kN is applied at the end of a cantileve...

Strength of Materials

A horizontal force 1 kN is applied at the end of a cantilever bent of diameter 40 mm as shown in Fig. 2.22. Determine maximum principal normal stresses 200 mm above the base.

Screenshot 2022-10-12 210616

The "Step-by-Step Explanation" refers to a detailed and sequential breakdown of the solution or reasoning behind the answer. This comprehensive explanation walks through each step of the answer, offering you clarity and understanding.
Our explanations are based on the best information we have, but they may not always be right or fit every situation.

The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

This Question has been Answered.

Already have an account?

Related Answered Questions

Question: 2.22

Figure 2.30(a) shows an element under axial stress 20 MPa and 50 MPa along with shear stress 40 MPa in x-y plane. Determine the state of stress in x’ – y’ plane at 30° counter-clockwise to x-y plane. ...

Verified Answer:

Equation (2.11b) can be used to cal-culate stresse...

Question: 2.21

Write a computer program to calculate normal and shear stress on any inclined plane. It should calculate principal stresses and their location. Input data for the program will be the direct and shear stresses on two mutually perpendicular planes (σx, σy, τxy) and the angle of the inclined plane. ...

Verified Answer:

The following computer program in Qbasic will solv...

Question: 2.20

Tensile stresses of 100 MPa and 50 MPa are acting on two perpendicular planes in a body. Determine the resultant stress inclined at 35° to the major principal plane using stress ellipsoid. ...

Verified Answer:

Draw two circles corresponding to the principal st...

Question: 2.19

Figure 2.28 shows the state of stress at a point. Determine the stress tensor on x’y’z’ reference frame rotated such that x’-axis makes equal angle with x, y, z directions in first quadrant and y’-axis makes 60° with x-axis. ...

Verified Answer:

Using simpler notations for direction cosines, let...

Question: 2.18

Figure 2.28 shows the state of stress at a point. Determine the principal normal and shear stresses and the orientation at which they act. Also determine the octahedral normal and shear stresses. ...

Verified Answer:

Stress tensor,

\left[\tau _{ i j}\right]=\b...

Question: 2.17

Solve Example 2.16 if the rotation of xyz reference is 30° clockwise. ...

Verified Answer:

Direction cosine matrix for transformation (Fig. 2...

Question: 2.16

he state of stress at a point in xyz reference is as follows. τ = |80 -60 0 -60 -40 0 0 0 40|MPa Determine the stress tensor in the direction x’y’z’ by rotating xyz through 30° anticlockwise about z-direction as shown in Fig. 2.26. ...

Verified Answer:

Direction cosines,

c_{x^{\prime} x}=\cos 30...

Question: 2.15

A cantilever 50 mm diameter is to carry an axial load 50 kN at an eccentricity of 5 mm below horizontal diameter in the vertical plane of symmetry along with a torque of 1.5 x 10^6 N mm as shown in Fig. 2.24. Calculate the stresses on a plane, normal of which is inclined at 30° clockwise to axis ...

Verified Answer:

Consider an element at a lowermost point P. Direct...

Question: 2.13

A cylindrical pressure tank of mean diameter 1.6 m, is fabricated by butt welding a 8 mm thick plate along a helix which forms an angle of 20° with the transverse plane. The end caps are spherical having wall thickness 10 mm. If the internal gauge pressure is 0.8 MPa, determine, (a) stresses in ...

Verified Answer:

(a) Cylindrical tank: First consider the equilibri...

Question: 2.12

solve example 2.11 using Mohr’s circle. ...

Verified Answer:

Plot the three stresses on a straight line

...