Question 10.6: A vessel flange uses 16 2 in. diameter bolts. Flange stress ...

Structural Analysis and Design of Process Equipment

A vessel flange uses 16 2 in. diameter bolts. Flange stress calculations indicate that a flange thickness of t =4.5 in. is adequate. The bolt circle diameter is C =22.5 in. Will secondary bending stresses be developed?

The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

Related Answered Questions

Question: 10.14

A spherically dished head is to be bolted to the welding-neck flange described in Example 10.9. The dished head is to be attached at the upper inner corner with the outer surface even with the ring’s outer surface (see Figure 10.25). What is the minimum required thickness of the flange ring when ...

Verified Answer:

From the geometry mentioned in Example 10.9, A = 2...

Question: 10.13

A welding-neck flange with the same geometry as that mentioned in Example 10.9 except for the thickness is used with a full-face gasket. The design pressure is 320 psi, and the “soft” gasket is vegetable fiber with m =1.75 and y=1100. What is the minimum required thickness? ...

Verified Answer:

1) Determine the lever arms of the inner and outer...

Question: 10.12

With the reverse flange given in Example 10.11, what is the minimum required thickness based on an allowable flange stress of 17,500 psi? ...

Verified Answer:

The tangential flange stress at the flange bore of...

Question: 10.11

A reverse flange is joined to a regular ring-type joint flange to form a reducing connection. The total bolt-up moment is controlling and equal to M0 =2,613,000. The flange bore B′ =13.25 in., the outside diameter A=26.5 in., and the flange thickness t =5 in. What is the tangential flange stress ...

Verified Answer:

The tangential flange stress

S_{T}

...

Question: 10.10

What is the minimum required thickness of a ring flange with the same design data as given in Example 10.9? The inside diameter has been increased to fit over the outside of the shell to where B=12.75 in. The bolt loadings and bolt size are the same as mentioned in Example 10.9. A sample ...

Verified Answer:

1) Calculate the total flange moment for design co...

Question: 10.9

What is the minimum required thickness of a welding neck flange as shown in Figure 10.15 with the following design data? (Note: These data are the same as those used for the blind flange in Example 10.8. In Figure 10.16 is a sample calculation for a welding neck flange.) Design pressure P =2500 ...

Verified Answer:

Figure 10.15 Flange dimensions mentioned in Exampl...

Question: 10.8

Considering the pressure vessel described in Example 10.5, the vessel is to have one end closed by a blind flange. What is the minimum required thickness of the blind flange? Design data are as follows: Design pressure P =2500 psi Design temperature=250 °F Flange material is SA-105 Bolting ...

Verified Answer:

Following the information calculated in Example 10...

Question: 10.7

Suppose that a vessel requires 24 2 – 1/2 in. diameter bolts on a flange that is 5.5 in. thick. What is the maximum bolt circle that will not cause secondary bending stresses? The minimum bolt spacing for 2 1/2 in. diameter bolts is 5 1/4 in. ...

Verified Answer:

The maximum spacing is

2 d+t=2 \times 2 \f...

Question: 10.5

A vessel has the following design data: design pressure P =2500 psi; design temperature=250 °F; a spiral-wound metal, fiber-filled stainless-steel gasket with inside diameter 13.75 in. and width N =1.0 in. The gasket factors are m =3.0 and y=10,000. Bolts are SA-325 Grade 1 with Sa =Sb =19,200 ...

Verified Answer:

Determine the effective gasket seating width as fo...

Question: 10.4

Determine the minimum corner radius to make the solution to Example 10.1 acceptable (valid). ...

Verified Answer:

The cylindrical-shell thickness

t_{s}[/lat...