Combined Bending and Torsional Stresses Problem Find the most highly stressed locations on the bracket shown in Figure 4-30 and determine the applied and principal stresses at those locations. Given The rod length l = 6 in and arm a = 8 in. The rod outside diameter d = 1.5 in. Load F = 1 000 lb.

Question

Combined Bending and Torsional Stresses

Problem Find the most highly stressed locations on the bracket shown in Figure 4-30 and determine the applied and principal stresses at those locations.

Given The rod length [latex]l[/latex] = 6 in and arm [latex]a[/latex] = 8 in. The rod outside diameter [latex]d[/latex] = 1.5 in. Load [latex]F[/latex] = 1 000 lb.

Assumptions The load is static and the assembly is at room temperature. Consider shear due to transverse loading as well as other stresses.

Accepted Answer

See Figures 4-30 to 4-33.

1 We will limit our investigation to the rod which is loaded both in bending (as a cantilever beam) and in torsion. (The arm would also need to be analyzed for a complete design.) First, the load distributions over the rod’s length need to be determined by drawing shear, moment, and torque diagrams for the rod.

2 The shear and moment diagrams will look similar to those for the cantilever beam in Example 4-5, the difference being that this force is at the end of the beam rather than at some intermediate point. Figure 4-31 shows that the shear force is uniform across the beam length and its magnitude is equal to the applied load [latex]V_{max} = F[/latex]= 1 000 lb. The maximum moment occurs at the wall and its magnitude is [latex]M_{max} = Fl[/latex] = (1 000) (6) = 6 000 lb-in. (See Example 4-5 for derivations.)

The torque applied to the rod is due to the force [latex]F[/latex] acting at the end of the 8-in arm and is [latex]T_{max} = Fa[/latex] = (1 000) (8) = 8 000 lb-in. Note that this torque is uniform over the length of the rod as it can only be reacted against by the wall. Figure 4-31 shows all three of these loading functions. It is clear from these plots that the most heavily loaded cross section is at the wall, where all three loads are maximum.

3 We will now take a section through the rod at the wall and examine the stress distributions within it due to these external loads. Figure 4-32a shows the distribution across the section of the normal bending stresses, which are a maximum (+/–) at the outer fibers and zero at the neutral axis. The shear stress due to transverse loading is a maximum at all points in the neutral ([latex]xz[/latex]) plane and zero at the outer fibers (Figure 4-32b).

The shear stress due to torsion is proportional to the radius so is zero at the center and a maximum at all points on the outer surface as shown in Figure 4-32c. Note the differences between the distributions of the normal bending stress and the torsional shear stress. The bending stress magnitude is proportional to the distance [latex]y[/latex] from the neutral plane and so is maximum at only the top and bottom of the section, whereas the torsional shear stress is maximal all around the perimeter.

4 We choose two points, [latex]A[/latex] and [latex]B[/latex] of Figure 4-30, to analyze (also shown in Figure 4-33a) because they have the worst combinations of stresses. The largest tensile bending stress will be in the top outer fiber at point [latex]A[/latex], and it combines with the largest torsional shear stress that is all around the outer circumference of the rod. A differential element taken at point [latex]A[/latex] is shown in Figure 4-33b. Note that the normal stress ([latex]\sigma _{x}[/latex]) acts on the [latex]x[/latex] face in the [latex]x[/latex] direction and the torsional shear stress ([latex] au _{xz}[/latex]) acts on the [latex]x[/latex] face in the [latex]+z[/latex] direction.

At point [latex]B[/latex] the torsional shear stress has the same magnitude as at point [latex]A[/latex], but the direction of the torsional shear stress ([latex] au _{xy}[/latex]) at point [latex]B[/latex] is 90° different than at point [latex]A[/latex]. The shear stress due to transverse loading ([latex] au _{xy}[/latex]) is a maximum at point [latex]B[/latex]. Note that these shear stresses both act in the [latex]–y[/latex] direction on the [latex]x[/latex] face at point [latex]B[/latex] as shown in Figure 4-33c. The transverse and torsional shear stresses then add at point [latex]B[/latex].

5 Find the normal bending stress and torsional shear stress on point A using equations 4.11b (p. 156) and 4.19b (p. 163), respectively.

[latex] \sigma_{\max }=\frac{M c}{I} [/latex] (4.11b)

[latex] M=\int V d x+C_1 x+C_2 \quad \quad 0

[latex] \sigma_x=\frac{M c}{I}=\frac{(F l) c}{I}=\frac{1000(6)(0.75)}{0.249}=18108 psi [/latex] (a)

[latex] au_{x z}=\frac{T r}{J}=\frac{(F a) r}{J}=\frac{1000(8)(0.75)}{0.497}=12072 psi [/latex] (b)

6 Find the maximum shear stress and principal stresses that result from this combination of applied stresses using equations 4.6 (p. 145)

[latex] \begin{aligned} \sigma_a, \sigma_b &=\frac{\sigma_x+\sigma_y}{2} \pm \sqrt{\left\lgroup\frac{\sigma_x-\sigma_y}{2} ight group ^2+ au_{x y}^2} \ \sigma_c &=0 \end{aligned} [/latex] (4.6a)

[latex] au_{\max }= au_{13}=\frac{\left|\sigma_1-\sigma_3 ight|}{2} [/latex] (4.6b)

[latex] \begin{aligned} au_{\max } &=\sqrt{\left\lgroup \frac{\sigma_x-\sigma_z}{2} ight group ^2+ au_{x z}^2}=\sqrt{\left\lgroup\frac{18108-0}{2} ight group ^2+12072^2}=15090 psi \ \sigma_1 &=\frac{\sigma_x+\sigma_z}{2}+ au_{\max }=\frac{18108}{2}+15090=24144 psi \ \sigma_2 &=0 \ \sigma_3 &=\frac{\sigma_x+\sigma_z}{2}- au_{\max }=\frac{18108}{2}-15090=-6036 psi \end{aligned} [/latex] (c)

7 Find the shear due to transverse loading at point [latex]B[/latex] on the neutral axis. The maximum transverse shear stress at the neutral axis of a round rod was given as equation 4.15c (p. 161).

[latex] au_{\max }=\frac{4}{3} \frac{V}{A} [/latex] (4.15c)

[latex] au_{ ext {transverse }}=\frac{4 V}{3 A}=\frac{4(1000)}{3(1.767)}=755 psi [/latex] (d)

Point [latex]B[/latex] is in pure shear. The total shear stress at point [latex]B[/latex] is the algebraic sum of the transverse shear stress and the torsional shear stress, which both act on the same planes of the differential element.

[latex] au_{\max }= au_{ ext {torsion }}+ au_{ ext {transverse }}=12072+755=12827 psi [/latex] (e)

which from equation 4.6 or the Mohr’s circle can be shown to be equal to the largest principal stress for this point.

8 Point A has the larger principal stress in this case, but note that the relative values of the applied torque and moment determine which of these two points will have the higher principal stress. Both points must then be checked. See files EX04-10 on CD.

Question 4.10: Combined Bending and Torsional Stresses Problem Find the mos...

Related Answered Questions

Crimping-Tool Stress and Deflection Analysis Problem Determine the stresses and deflections at critical points in the crimping tool shown in Figures 3-3 (repeated here) and 4-49. Given The geometry and loading are known from Case Study 2A on p. 84. The thickness of link 1 is 0.313 in, of links 2 ...

Verified Answer:

Verified Answer:

Automobile Scissors-Jack Stress and Deflection Analysis Problem Determine the stresses and deflections at critical points in the scissors-jack assembly shown in Figures 3-5 (repeated here) and 4-52. Given The geometry and loading are known from Case Study 3A (p. 88). The design load is 2 000 lb ...

Verified Answer:

Verified Answer:

Column Design for Concentric Loading Problem: A beachfront house is to be jacked up 10 ft above grade and placed on a set of steel columns. The weight to be supported by each column is estimated to be 200 000 lb. Two designs are to be considered, one using square steel tubes and the other using ...

Verified Answer:

Design of a Torsion Bar Problem: Determine the best cross-sectional shape for a hollow torsion bar to be made from a sheet of steel of known dimensions in order to withstand a pure torsional load with minimum angular deflection. Also find the maximum shear stress. Given: The applied torque is 10 ...

Verified Answer:

Finding Reactions of a Statically Indeterminate Beam Using Castigliano’s Method Problem: Find the reaction forces for the indeterminate beam in Figure 4-22e. Given: The load is uniformly distributed over the beam as shown. Length is l. The magnitude of the distributed force is w. Assumptions: ...

Verified Answer:

Finding Reactions and Deflection of Statically Indeterminate Beams Using Singularity Functions Problem: Determine and plot the loading, shear, moment, slope, and deflection functions for the beam in Figure 4-22d. Find maximum deflection. Given: The load is uniformly distributed over part of the ...

Verified Answer:

Verified Answer:

Finding Beam Slope and Deflection of an Overhung Beam Using Singularity Functions Problem: Determine and plot the slope and deflection functions for an overhung beam with a uniformly distributed load over part of its length and a concentrated force at its end as shown in Figure 4-22c (p. 165). ...

Verified Answer: