Holooly Plus Logo
Holooly Plus Logo

Question 7.Q.12: Complete the waveform (timing) diagrams shown in Figures 7.2...

Complete the waveform (timing) diagrams shown in Figures 7.25 and 7.26.

7.25
7.26
The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

See Figure A.18.

A.18

Related Answered Questions

Question: 7.Q.11

How many clock pulses does it take for: (a) the data ABCD = 1101 to be fully stored in the register (b) the register to be empty? ...

Verified Answer:

See Figure A.17.
Question: 7.PE.8

To investigate the universal shift register For this exercise you will need the following components and equipment: 1 – 74LS194 ic (4-bit universal shift register with positive edge triggering) 4 – LED (5 mm) and resistor (270 Ω) 1 – +5 V dc power supply The pin connections for the 74194 are shown ...

Verified Answer:

Procedure (a): serial in-parallel out 1 Clear the ...
Question: 7.PE.7

To investigate the 4-bit parallel load shift register For this exercise you will need the following components and equipment: 2 – 74LS76 ic (dual JK flipflop) 4 – LED (5 mm) and resistor (270 Ω) 1 – +5 V dc power supply ...

Verified Answer:

1 Connect up the circuit shown in Figure 7.20. Ref...
Question: 7.PE.6

To investigate the 4-bit serial load shift register using D flipflops For this exercise you will need the following components and equipment: 2 – 74LS74 ic (dual D flipflop) 4 – LED (5 mm) and resistor (270 Ω) 1 – +5 V dc power supply The circuit is shown in Figure 7.17 and the pin connections for ...

Verified Answer:

Procedure 1 Clear the register by setting all the ...
Question: 7.Q.13

Complete the waveform (timing) diagrams shown in Figures 7.25 and 7.26. ...

Verified Answer:

See Figure A. 19.
Question: 7.Q.9

A certain 4-bit shift register uses a clock frequency of 4 MHz. What time is needed to load the register (a) in series (b) in parallel? How many clock pulses are needed for each method respectively? ...

Verified Answer:

(a) 1 μs , 4 (b) 0.25 μs , 1
Question: 7.Q.6

A 4-bit shift register reads ABCD = 1011. List the contents of the register (as ABCD) shifting right, after (a) one clock pulse (b) two clock pulses (c) three clock pulses (d) four clock pulses ...

Verified Answer:

6       (a) 0101 (b) 0010 (c) 0001 (d) 0000
Question: 7.PE.4

To investigate the 4-bit synchronous up counter For this exercise you will need the following components and equipment: 1 – 74LS161 ic (4-bit synchronous binary counter) 1 – 74LS00 ic (quad 2-input NAND) 4 – LED red (5 mm) and resistor (270 Ω), for the Q outputs 1 – LED green (5 mm) and resistor (2 ...

Verified Answer:

Procedure (a): to count to decimal 16 1 Make up a ...
Question: 7.PE.5

To investigate the 4-bit synchronous up-down counter For this exercise you will need the following components and equipment: 1 – 74LS192 ic (4-bit synchronous up-down BCD counter) 4 – LED red (5 mm) and resistor (270 Ω), for the Q outputs 1 – LED green (5 mm) and resistor (270 Ω), for the carry ...

Verified Answer:

Procedure (a): to count up 1 Make the following se...
Question: 7.PE.3

To investigate the action of the 3-bit synchronous counter For this exercise you will need the following components and equipment: 2 – 74LS76 ic (dual JK flipflop) 1 – 74LS08 ic (quad 2-input AND) 3 – LED red (5 mm) and resistor (270 Ω) 1 – LED green (5 mm) and resistor (270 Ω) 1 – +5 V dc power ...

Verified Answer:

1 Make up the circuit of Figure 7.10. See Figure 6...