Holooly Plus Logo
Holooly Plus Logo

Question 3.9: Horizontal irregularity type 2: reentrant corner irregularit...

Horizontal irregularity type 2: reentrant corner irregularity
The building shown in Figure 3.23 has a reentrant corner with plan projections in the x- and y-directions of 20 ft and 16 ft, respectively. Determine if a horizontal type 2 irregularity exists.

fig3.23
The "Step-by-Step Explanation" refers to a detailed and sequential breakdown of the solution or reasoning behind the answer. This comprehensive explanation walks through each step of the answer, offering you clarity and understanding.
Our explanations are based on the best information we have, but they may not always be right or fit every situation.
The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.
This Question has been Answered.
Subscribe
Already have an account?
Login

Related Answered Questions

Question: 3.17

Vertical irregularity type 5a and 5b: weak and extreme weak story The shear strengths are given for the piers of the three-story (concrete masonry unit [CMU]) masonry building shown in Figure 3.32, in Table 3.7. Determine if a weak story irregularity exists. ...

Verified Answer:

The total shear at each floor level is calculated ...
Question: 3.7

Determination of a diaphragm design seismic force low-rise building For the building discussed in Example 3.4 the following seismic data apply: • Seismic design category D • Design spectral acceleration SDS = 1.0 • Risk category II (ASCE 7 T 1.5-1) • Importance factor Ie = 1.0 (ASCE 7 T 1.5-2) ...

Verified Answer:

The seismic weight w_{px} includes ...
Question: 3.8

Horizontal irregularity type 1a and type 1b: torsional and extreme torsional irregularities The following displacements are given for a two-story rigid diaphragm SSMF building shown in Figure 3.22. Horizontal irregularities—Type 1a and 1b only apply to buildings with rigid and semirigid diaphragms. ...

Verified Answer:

The irregularity check is defined in terms of stor...
Question: 3.15

Vertical irregularity type 3: geometrical irregularity For the four-story braced frame building shown in Figure 3.30. Determine if a type 3 irregularity exists. ...

Verified Answer:

The lateral force resisting system on the second l...
Question: 3.6

Determine diaphragm design force Determine the diaphragm design force Fpx at each floor of the building. Floor and roof diaphragm seismic design forces are determined in accordance with Fpx = ∑i=x^n Fi/∑i=0^n wi wpx (3.24) (ASCE 7 Equation 12.10-1) where: Fpx is the diaphragm design force Fi is ...

Verified Answer:

The value of F_{px} should not be l...
Question: 3.16

Vertical irregularity type 4: in-plane discontinuity in vertical lateral-force-resisting element irregularity The offset of the vertical lateral force resisting system is 60 ft, which is greater than the bay width of the lateral system (Figure 3.31). ...

Verified Answer:

Thus, an in-plane discontinuity in vertical latera...
Question: 3.4

A flexible diaphragm analysis A roof plan and elevation of a single-story precast concrete tilt-up building with panelized wood roof (flexible roof diaphragm) is shown in Figure 3.14. A wind load of 25 (#/ft² ) is applied in the east-west direction (Figure 3.15). 1. Determine the wind force ...

Verified Answer:

1. Summing moments about A to determine the wind l...
Question: 3.3

Determine the direct and torsional wall shears For the building discussed in Example 3.1 determine the shear force in walls A, B, C, D, and E for a seismic force V = 150 kips applied in the y-direction. J = 26,793.7 ft² and e = 13.3′. ...

Verified Answer:

The total shear in the walls (A, B, and C) paralle...
Question: 3.2

Locating the center of rigidity For the building discussed in Example 3.1, determine the location of the center of rigidity (CR) and the value of the torsional rigidity, J, for the lateral force resisting system configuration as shown. ...

Verified Answer:

The walls of the multistory building in Example 3....
Question: 3.1

Locating the center of mass of a building A plan view of a typical floor of a multistory building is shown in Figure 3.3. Concrete shear walls resist lateral forces in both directions. Determine the location of the center of mass (CM) at the given floor level. The mass of the floor diaphragm is ...

Verified Answer:

The center of mass coordinates can be determined b...