Question 15.7: Solve Example 15.6 using Michalowski’s solution.

Principles of Geotechnical Engineering

Solve Example 15.6 using Michalowski’s solution.

The "Step-by-Step Explanation" refers to a detailed and sequential breakdown of the solution or reasoning behind the answer. This comprehensive explanation walks through each step of the answer, offering you clarity and understanding.
Our explanations are based on the best information we have, but they may not always be right or fit every situation.

The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

This Question has been Answered.

Already have an account?

Related Answered Questions

Question: 15.10

Solve Example 15.9 using Spencer’s solution (Figure 15.35). ...

Verified Answer:

Given: H = 21.62 m, β = 26.57°, c′ = 20 kN/m², γ =...

Question: 15.11

Solve Example 15.9 using Michalowski’s solution (Figure 15.36). ...

Verified Answer:

\frac{c^\prime}{\gamma H \tan \phi^\prime}=...

Question: 15.9

A given slope under steady-state seepage has the following: H = 21.62 m, Φ′ = 25°, slope: 2H:1V, c′ = 20 kN/m², γ = 18.5 kN/m³, ru = 0.25. Determine the factor of safety, Fs. Use Table 15.3. ...

Verified Answer:

\beta=\tan^{-1}\left(\frac{1}{2}\right)=26....

Question: 15.6

A slope with β = 45° is to be constructed with a soil that has Φ′ = 20° and c′ = 24 kN/m². The unit weight of the compacted soil will be 18.9 kN/m³. a. Find the critical height of the slope. b. If the height of the slope is 10 m, determine the factor of safety with respect to strength. ...

Verified Answer:

Part a We have

m=\frac{c^\prime}{\gamma H_{...

Question: 15.5

A cut slope in saturated clay (Figure 15.21) makes an angle of 56° with the horizontal. Assume kh = 0.25. a. Determine the maximum depth up to which the cut could be made. b. How deep should the cut be made if a factor of safety of 2 against sliding is required? ...

Verified Answer:

Part a For the critical height of the slopes, [lat...

Question: 15.4

A cut slope was excavated in a saturated clay. The slope made an angle of 40° with the horizontal. Slope failure occurred when the cut reached a depth of 6.1 m. Previous soil explorations showed that a rock layer was located at a depth of 9.15 m below the ground surface. Assuming an undrained ...

Verified Answer:

Part a Referring to Figure 15.13,

D=\frac{9...

Question: 15.3

A cut slope is to be made in a soft saturated clay with its sides rising at an angle of 60° to the horizontal (Figure 15.17). Given: cu = 40 kN/m² and γ = 17.5 kN/m³. a. Determine the maximum depth up to which the excavation can be carried out. b. Find the radius, r, of the critical circle when ...

Verified Answer:

Part a Since the slope angle β = 60° > 53°, the...

Question: 15.2

A cut is to be made in a soil having γ = 105 lb/ft³, c′ = 600 lb/ft², and Φ′ = 15°. The side of the cut slope will make an angle of 45° with the horizontal. What should be the depth of the cut slope that will have a factor of safety (Fs) of 3? ...

Verified Answer:

Given:

\phi ^\prime

= 15°; c′ = 60...

Question: 15.8

For the slope shown in Figure 15.31, find the factor of safety against sliding for the trial slip surface AC. Use the ordinary method of slices. ...

Verified Answer:

The sliding wedge is divided into seven slices. No...

Question: 15.1

For the infinite slope with a steady state seepage shown in Figure 15.9, determine: a. The factor of safety against sliding along the soil-rock interface. b. The height, H, that will give a factor of safety (Fs) of 2 against sliding along the soil-rock interface. ...

Verified Answer:

Part a From Eq. (15.17),

F_s=\frac{c^\prime...