Question A8.14: The voltage appearing at the secondary winding of a transfor...

Electronic Circuits Fundamentals and Applications

The voltage appearing at the secondary winding of a transformer is shown in Fig. A8.19. Determine:
(a) the period of the voltage
(b) the value of the voltage when (i) t = 5 ms and
(ii) t = 35 ms
(c) the maximum and minimum values of voltage
(d) the average value of the voltage during the time interval 0 to 40 ms
(e) the equation for the voltage.

The "Step-by-Step Explanation" refers to a detailed and sequential breakdown of the solution or reasoning behind the answer. This comprehensive explanation walks through each step of the answer, offering you clarity and understanding.
Our explanations are based on the best information we have, but they may not always be right or fit every situation.

The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

This Question has been Answered.

Already have an account?

Related Answered Questions

Question: A8.18

A capacitor is charged to a potential of 100 V. It is then disconnected from its charging source and left to discharge through a resistor. If it takes 10 s for the voltage to fall to 50 V, how long will it take to fall to 10 V? ...

Verified Answer:

Here we are dealing with exponential decay. If we ...

Question: A8.17

An amplifier has a power gain of 33 dB. What input power will be required to produce an output power of 11 W? ...

Verified Answer:

Now power gain expressed in decibels will be given...

Question: A8.16

An amplifier has a power gain of 27,000. Express this in Bels (B) and decibels (dB). ...

Verified Answer:

In Bels, power gain =

\log _{10}

(27,...

Question: A8.15

Part of the control logic for an intruder alarm is shown in Fig. A8.31. Determine the logic required to select the Y4 output and verify that the Y3 output is permanently selected and unaffected by the states of S1 and S2. ...

Verified Answer:

Each logic gate shown in Fig. A8.31 is a two-input...

Question: A8.13

The voltage applied to a high voltage rectifier is given by the equation: ν = 800 sin(314 t) Determine the voltage when: (a) t = 1 ms (b) t = 15 ms. ...

Verified Answer:

We can easily solve this problem by substituting v...

Question: A8.12

The following data were obtained while making measurements on an N-channel field effect transistor: ...

Verified Answer:

The data have been shown plotted in Fig. A8.10. No...

Question: A8.11

The impedance of the a.c. circuit shown in Fig. A8.5 is given by: Z=√ R^{2} + X^{2} ...

Verified Answer:

Here we know that: R = 25 Ω Z = 50 Ω X = ? First w...

Question: A8.10

The frequency of resonance, f, of a tuned circuit (see Fig. A8.4) is given by the relationship: f=1/2√LC ...

Verified Answer:

Here we know that: C = 100 pF = 100 ×

10^{-...

Question: A8.9

The reactance, X, of a capacitor is given by the relationship: Find the value of capacitance that will exhibit a reactance of 10 kΩ at a frequency of 400 Hz. ...

Verified Answer:

First, let’s summarize what we know: X = 10 kΩ f =...

Question: A8.8

A copper wire has a length, l, of 1.5 km, a resistance, R, of 5 Ω and a resistivity, ρ, of 17.2 × 10^{-6} Ω mm. Find the cross-sectional area, a, of the wire, given the following relationship: ...

Verified Answer:

Once again, it is worth getting into the habit of ...