To increase the heat transfer rate from the box in Illustrative Problem 11.17, a vertical fin is added to each of the four sides (see Figure 11.36). The fins are aluminum, 15 cm high and 0.15 cm thick, and protrude 3 cm from the box. Find the new heat loss rate.

Question

Accepted Answer

The fins are vertical plates with the same characteristic length as the sides of the box, so the fin’s heat transfer coefficient is the same as in Problem 11.17: [latex]h_{c}[/latex] = 5.102 W/m2 °C.

Here P = 0.303 m, k = 204.2 W/m °C per Table 11.1, d = 0.03 m, [latex]A_{f}[/latex]= 0.0369 [latex]m^{2}[/latex] (4 fins) and a = 0.000225 [latex]m^{2}[/latex]. The value of m in Equation 11.48a is thus

[latex]m=\sqrt{\frac{P h_{c}}{k a}} \sqrt{\frac{0.303 imes 5.102}{204.2 imes 0.000225}}=5.80 m ^{-1}[/latex]

and md = 0.174. The tanh of md = 0.172 and (tanh md)/md = 0.99. Thus, the fin heat transfer rate is

[latex]Q_{f}=\eta h_{c} A_{f}(\Delta t)=0.99 imes 5.102 imes 0.0369 imes 25=4.66 W[/latex]

This rate added to the rate for the box brings the total heat transfer rate to 18.81 watts, which is an increase of 33% due to the usage of fins.

Note that when fins are added, the surface area of the box exposed to convection is diminished. In this example, the reduction is negligible.

Question 11.30: To increase the heat transfer rate from the box in Illustrat...

Related Answered Questions

A bare steel pipe of outside diameter 3.50 in. runs through a room whose walls are at 70°F. Determine the heat loss by radiation from 5 ft. of the pipe if its outside temperature is 120°F. ...

Verified Answer:

A heat exchanger has one shell pass and two tube passes similar to Figure 11.27c. Oil flows in the tube side and is cooled from 280°F to 140°F. On the shell side, water is heated from 85°F to 115°F. Determine the true mean temperature difference. ...

Verified Answer:

Using Table 11.6 for the appropriate fouling factors, calculate the surface required for Illustrative Problem 11.27. ...

Verified Answer:

If the best exchanger in Illustrative Problem 11.26 is operated in parallel flow, determine the outside tube surface required. ...

Verified Answer:

A counterflow heat exchanger is used to cool a flow of 400 lb./min of lubricating oil. Hot oil enters at 215°F and leaves at 125°F. The specific heat of the oil is 0.85 Btu/lb.·°F, and the overall coefficient of heat transfer of the unit ...

Verified Answer:

A steel pipe, k = 26 Btu/(h·ft.·°F), having an outside diameter of 3.5 in. and an inside diameter of 3.00 in., and 5 ft. long, is covered with 1 in. of mineral wool, k = 0.026 Btu/ (h·ft.·°F). ...

Verified Answer:

Determine the overall heat-transfer coefficient for the composite wall of Illustrative Problem 11.4 if h on the hot side is 0.9 Btu/(h·ft .^2·°F) and h on the cold side is 1.5 Btu/(h·ft .^2·°F). ...

Verified Answer:

Solve Illustrative Problem 11.16 taking into account both convection and radiation. ...

Verified Answer:

Determine the radiation heat-transfer coefficient for the pipe of Illustrative Problem 11.21. ...

Verified Answer:

If instead of water, atmosphere pressure air was flowing in the tube of Illustrative Problem 11.19, determine the inside film coefficient. ...

Verified Answer: