Question 6.P.12: To obtain an estimate of the damping in the system shown in ...

Dynamics of Structures

To obtain an estimate of the damping in the system shown in Problem $6.1$ , end $B$ is displaced $32 \mathrm{~mm}$ and the system is allowed to vibrate freely. The amplitude decays to $6 \mathrm{~mm}$ in 5 cycles. If the damping is assumed to be viscous in nature, what will be the maximum amplitude of $B$ due to the rotation of eccentric flywheel.

The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

Related Answered Questions

Question: 6.P.3

An electric motor weighing 1160 N is attached to a floor beam which deflects 0.76 mm under the weight. The armature of the motor weighs 40 kg. As the motor is run up gradually to operating speed of 1600 RPM, it is observed that the maximum amplitude of oscillation is 2.5 mm, decreasing to 0.5 mm at ...

Verified Answer:

1467 N ·s/m, 0.805 mm

Question: 6.P.14

Using an eccentric mass shaker, a dynamic test was run on a structure in which the exciting frequency was varied over a range of values. For each frequency, the response amplitude as well as the phase angle were measured and the following data was obtained. The estimated natural frequency of the ...

Verified Answer:

ξ = 0.105

Question: 6.P.16

In order to measure the characteristics of friction dampers used in earthquake-resistant construction, laboratory tests are conducted on a scaled model of a single-story frame as shown in Figure P6.16. In a free vibration test, the amplitude of motion of the frame reduces from 3/4 in. to 1/64 in. ...

Verified Answer:

0.116 in.

Question: 6.P.9

An accelerometer has a natural frequency of 40 rad/s and a damping ratio of 0.6. It is calibrated to read correctly the input acceleration at very low frequencies. Find the calibration factor. An input signal given by ug=4sin⁡(4πt)+3sin⁡(5πt)m/s² is supplied to the accelerometer. Plot the output ...

Verified Answer:

Calibration factor

=1,600

. Measured...

Question: 6.P.7

A seismic instrument designed to measure vertical acceleration consists of a light beam AB pivoted at A through a torsional spring of constant 20Nm (Fig. P6.7). A small body of mass 0.6 kg is fixed to the beam at end B and a viscous damper is attached at C. The pointer BED, pivoted to the 0.6 kg ...

Verified Answer:

ω = 48.11 rad/s, c = 90.94 N ·s/m. Calibration fac...

Question: 6.P.5

A machine weighing 900 N is supported on springs of total stiffness 700 N/mm. Unbalance results in a disturbing force of 360 N at a speed of 3000 RPM. Damping is estimated at 20% of critical value. Determine (a) the amplitude of motion (b) the transmissibility (c) the transmitted force ...

Verified Answer:

(a) 0.0428 mm, (b) 0.1457, (c) 52.46 N

Question: 6.P.1

Two uniform parallel beams AB 1.2 m long, weighing 20 kg each, are hinged at A and supported at B by a spring of stiffness 4.33 N/mm as shown in Figure P6.1. The beams carry a flywheel of mass 132 kg attached at D,1.0 m away from the hinge. The flywheel is rotating at 200 RPM and its center of ...

Verified Answer:

(a)

6.42  \mathrm{rad} / \mathrm{s}

...

Question: 6.8

A water tower with a total weight of 50 kips is represented by a single-degree-of-freedom system. The total stiffness of the supporting columns is estimated at 52 kips/in. In a test the tower is subjected to a harmonic excitation at a frequency of 10 rad/s and the force displacement relationship is ...

Verified Answer:

(a) For viscous damping, the energy loss per cycle...

Question: 6.7

An accelerometer is designed to have a natural frequency of 30 rad/s and a damping ratio of 0.7. It is calibrated to read correctly the input acceleration at very small values of the exciting frequency. (a) What would be the percentage error in the instrument reading if the harmonic motion being ...

Verified Answer:

(a) From Equation 6.89a,

\rho =\frac{m A}{k...

Question: 6.6

A sensitive instrument that requires to be insulated from vibration is to be installed in a laboratory where a reciprocating machine is in use. The vibrations of the floor of the laboratory may be assumed to be a simple harmonic motion having a frequency in the range 1000 to 3000 cycles per minute. ...

Verified Answer:

The frequency ratio should be larger than

\...