Acceleration of Steam in a Nozzle Steam at 250 psia and 700°F steadily enters a nozzle whose inlet area is 0.2 ft^2. The mass flow rate of steam through the nozzle is 10 lbm/s. Steam leaves the nozzle at 200 psia with a velocity of 900 ft/s. Heat losses from the nozzle per unit mass of the steam

Question

Acceleration of Steam in a Nozzle

Steam at 250 psia and 700°F steadily enters a nozzle whose inlet area is 0.2 ft[latex]^2[/latex]. The mass flow rate of steam through the nozzle is 10 lbm/s. Steam leaves the nozzle at 200 psia with a velocity of 900 ft/s. Heat losses from the nozzle per unit mass of the steam are estimated to be 1.2 Btu/lbm. Determine (a) the inlet velocity and (b) the exit temperature of the steam.

Accepted Answer

Assumptions 1 This is a steady-flow process since there is no change with time at any point and thus [latex]\Delta m_{\mathrm{CV}}=0[/latex] and [latex]\Delta E_{\mathrm{CV}}=0[/latex]. 2 There are no work interactions. 3 The potential energy change is zero, Δ pe =0.

Analysis We take the nozzle as the system (Fig. 5-26). This is a control volume since mass crosses the system boundary during the process. We observe that there is only one inlet and one exit and thus [latex]\dot{m}_{1}=\dot{m}_{2}=\dot{m}[/latex].
(a) The specific volume and enthalpy of steam at the nozzle inlet are

[latex]\left.\begin{array}{ll}P_{1}=250 \mathrm{psia} \T_{1}=700^{\circ} \mathrm{F}\end{array} ight\} \quad \begin{aligned}&v_{1}=2.6883 \mathrm{ft}^{3} / \mathrm{lbm} \&h_{1}=1371.4 \mathrm{Btu} / \mathrm{lbm}\end{aligned}[/latex] (Table A-6E)

Then,

[latex]\begin{gathered}\dot{m}=\frac{1}{V_{1}} V_{1} A_{1} \\quad\10 \mathrm{lbm} / \mathrm{s}=\frac{1}{2.6883 \mathrm{ft}^{3} / \mathrm{lbm}}\left(V_{1} ight)\left(0.2 \mathrm{ft}^{2} ight) \\quad\V_{1}=134.4 \mathrm{ft} / \mathrm{s}\end{gathered}[/latex]

(b) Under stated assumptions and observations, the energy balance for this steady-flow system can be expressed in the rate form as

[latex]\underbrace{E_{ ext {in }}-E_{ ext {out}}}_{\begin{array}{c} ext { Rate of net energy transfer} \ ext { by heat, work, and mass }\end{array}} =\underbrace{{dE_{ ext {system }}}/dt earrow ^{0( ext{steady})}}_{\begin{array}{c} ext {Rate of Change in internal, kinetic, } \ ext { potential, etc., energies }\end{array}}=0[/latex]

[latex]\dot{E}_{ ext {in }} =\dot{E}_{ ext {out }} [/latex]

[latex]\dot{m}\left(h_{1}+\frac{V_{1}^{2}}{2} ight) =\dot{Q}_{ ext {out }}+\dot{m}\left(h_{2}+\frac{V_{2}^{2}}{2} ight) \quad( ext { since } \dot{W}=0, ext { and } \Delta ext { pe } \cong 0)[/latex]

Dividing by the mass flow rate [latex]\dot m[/latex] and substituting, [latex]h_{2}[/latex] is determined to be

[latex]h_{2} =h_{1}-q_{ ext {out }}-\frac{V_{2}^{2}-V_{1}^{2}}{2} [/latex]

[latex]=(1371.4-1.2) \mathrm{Btu} / \mathrm{lbm}-\frac{(900 \mathrm{ft} / \mathrm{s})^{2}-(134.4 \mathrm{ft} / \mathrm{s})^{2}}{2}\left(\frac{1 \mathrm{Btu} / \mathrm{lbm}}{25,037 \mathrm{ft}^{2} / \mathrm{s}^{2}} ight) [/latex]

[latex]=1354.4 \mathrm{Btu} / \mathrm{lbm}[/latex]

Then,

[latex]\left.\begin{array}{l}P_{2}=200 \mathrm{psia} \h_{2}=1354.4 \mathrm{Btu} / \mathrm{lbm}\end{array} ight\} \quad T_{2}=\mathbf{6 6 2 . 0}^{\circ} \mathbf{F} \quad [/latex] (Table A-6E)

Discussion Note that the temperature of steam drops by 38.0°F as it flows through the nozzle. This drop in temperature is mainly due to the conversion of internal energy to kinetic energy. (The heat loss is too small to cause any significant effect in this case.)

Question 5.5: Acceleration of Steam in a Nozzle Steam at 250 psia and 700°...

This Question has been Answered.

Already have an account?

Login

Related Answered Questions