Holooly Plus Logo
Holooly Plus Logo

Question B.15: Using PSpice/SPICE to plot the frequency response of a high-...

Using PSpice/SPICE to plot the frequency response of a high-pass CR circuit Use PSpice/ SPICE to plot the frequency response of the high-pass CR circuit in Fig. B.37(a). Assume V_{ m }=1 V (peak AC), R = 10 kΩ, and C = 0.1 µF. The frequency f varies from 1 Hz to 100 kHz.

The Blue Check Mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

The high-pass CR circuit for PSpice simulation is shown in Fig. B.38. The PSpice plots of the magnitude and phase angle are shown in Fig. B.39, which gives f_{ o }=157 Hz \text { at }-3 dB .

image_2021-11-18_204233
image_2021-11-18_204251

Related Answered Questions

Using PSpice/SPICE to plot the frequency response of a low-pass RC circuit Use PSpice/SPICE to plot the frequency response of the low-pass RC circuit in Fig. B.34(a). Assume Vm = 1 V (peak AC), R = 10 kΩ, and C = 0.1 µF. The frequency f varies from 1 Hz to 100 kHz.

Verified Answer:
The low-pass RC circuit for PSpice simulation is s...

Finding the frequency response of a parallel RLC circuit The parallel RLC circuit in Fig. B.44 has R = 50 Ω, L = 4 mH, and C = 0.15 µF. (a) Determine the parallel resonant frequency fp, the damping ratio δ, the cutoff frequencies, the bandwidth BWp, and the quality factor Qp of the circuit. (b) Use

Verified Answer:
(a) R=50 \Omega, L=4 mH , C=0.15 \mu F \te...

Finding the parallel resonant frequency The parameters of the parallel resonant RLC circuit in Fig. B.32(a) are RC1 = 47 Ω, L = 5 mH, C = 50 pF, RS = 20 kΩ, and the current source Is = 6 mA. Calculate (a) the parallel resonant frequency fp, (b) the voltage Vp across the resonant circuit at

Verified Answer:
R_{ C1 }=47 \Omega, L=5 mH , C=50 pF , R_{...

Finding the frequency response of a series RLC circuit The series RLC circuit in Fig. B.40 has R = 50 Ω, L = 4 mH, and C = 0.15 µF. (a) Determine the series resonant frequency fn, the damping ratio δ, the quality factor Qs, the cutoff frequencies, and the bandwidth BWs. (b) Use PSpice/SPICE to plot

Verified Answer:
(a) R=50 \Omega, L=4 mH \text {, and } C=0...

Finding Thevenin’s equivalent circuit Represent the network shown in Fig. B.11(a) by Thevenin’s equivalent, as shown in Fig. B.11(b). Assume VCC = 12 V, R1 = 15 kΩ, and R2 = 7.5 kΩ.

Verified Answer:
The open-circuit voltage, which is Thevenin’s volt...

Finding the output voltage using the superposition theorem A circuit with three input voltages VS1, VS2, and VS3 is shown in Fig. B.8. Use the superposition theorem to determine the output voltage VO. Use R1 = 2 kΩ, R2 = 4 kΩ, R3 = 6 kΩ, VS1 = 10 V, VS2 = 12 V, and VS3 = 15 V.

Verified Answer:
The equivalent circuit with source V_{ S 1...

Finding the effective time constant The circuit in Fig. B.49 has R1 = R2 = R3 = 10 kΩ and C1 = 0.1 µF. Determine (a) the effective time constant τ and (b) the cutoff frequency ωo.

Verified Answer:
If the source is shorted, the effective resistance...

Finding the effective time constant The circuit in Fig. B.48 has R1 = R2 = R3 = 6 kΩ and C = 0.1 µF. Determine (a) the effective time constant τ, (b) the cutoff frequency ωo, and (c) the bandwidth BW.

Verified Answer:
If the source is shorted, the effective resistance...

Pulse response of a parallel RC circuit A constant-current source iS = IS, shown in Fig. B.29(a), feeds a parallel RC circuit with C = 0.1 µF and R = 100 kΩ, as shown in Fig. B.29(b). The input is a pulse current of duration T = 0.5 ms. Determine (a) the instantaneous current iC(t) through

Verified Answer:
For a pulse signal, the input current in Laplace’s...

Using PSpice/SPICE to plot the pulse response of a CR circuit Use PSpice/SPICE to plot the output voltage vO(t) of the circuit in Fig. B.22(a) for τ = 0.1 ms, 1 ms, and 5 ms. Assume T = 2 ms and vS = VS = 1 V of pulse input.

Verified Answer:
For τ = 0.1 ms, let C = 0.1 µF. Then R=\fr...