Holooly Plus Logo
Holooly Plus Logo

Question 12.29: We wish to obtain the Bode plot for the filter designed in E...

We wish to obtain the Bode plot for the filter designed in Example 12.28. We will employ the op-amp model, in which R_i = ∞, R_o = 0, and A = 10^5, and plot over the frequency range from 600 to 60 kHz.

The "Step-by-Step Explanation" refers to a detailed and sequential breakdown of the solution or reasoning behind the answer. This comprehensive explanation walks through each step of the answer, offering you clarity and understanding.
Our explanations are based on the best information we have, but they may not always be right or fit every situation.
The Blue Check Mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

This Question has been Answered.

Subscribe

Already have an account?

Login

Related Answered Questions

Let us use the equations in Example 12.27 to design a band-pass filter of the form shown in Fig. 12.57 with a BW =2000 rad/s, (Vo/VS)(ω0) = -5, and Q = 3. Use C = 0.1 μF, and determine the center frequency of the filter.

Verified Answer:
Using the filter equations, we find that   [l...

The circuit in Fig. $12.66$ is a floating simulated resistor. For an ideal OTA, find an expression for Req = v1/i1. Using the OTA described in Example 12.30, produce an 80-kΩ resistance. Repeat for a 10-MΩ resistor.

Verified Answer:
For OTA 1, we have i_{o 1}=g_{m 1}\left(-v_...

Using the summer in Fig. 12.64, and the OTAs specified in Example 12.30, produce the following function Repeat for the function vo = 10 v1 + 2 v2  vo = 10 v1 – 2 v2

Verified Answer:
Comparing Eq. (12.79) (i_{o 1}=g_{m 1} v_{1...

The low-pass filter in Fig. 12.70 is implemented using a 25-pF capacitor and OTAs with a gm – IABC sensitivity of 20, a maximum gm of 1 mS, and 3 decades of range. Find the required bias currents for the filter transfer function:

Verified Answer:
Comparing Eq. (12.86) (\frac{\mathbf{V}_{\m...

Using the OTA’s specifications from Example 12.30 and 5 -pF capacitors, design a Tow-Thomas low-pass filter with a corner frequency of 6 MHz, Q = 5, and dc gain of 1 .

Verified Answer:
Using the v_{i 1}-v_{o 2} input-out...

The ac-dc converter in Fig. 12.74a is designed for use with a hand-held calculator. Ideally, the circuit should convert a 120-V rms sinusoidal voltage to a 9-V dc output. In actuality the output is vo(t) = 9 + 0.5 sin 377t V Let us use a low-pass filter to reduce the 60-Hz component of vo(t).

Verified Answer:
The Thévenin equivalent circuit for the converter ...

The antenna of an FM radio picks up stations across the entire FM frequency range-approximately 87.5 MHz to 108 MHz. The radio’s circuitry must have the capability to first reject all of the stations except the one that the listener wants to hear and then to boost the minute antenna signal.

Verified Answer:
Since \mathbf{V}(s)=\mathbf{V}_{A}(s)[/late...

Compact discs (CDs) have become a very popular medium for recording and playing music. CDs store information in a digital manner; that is, the music is sampled at a very high rate, and the samples are recorded on the disc. The trick is to sample so quickly that the reproduction sounds continuous.

Verified Answer:
Suppose, for example, that our specification for t...

The circuit in Fig. 12.84a is called a notch filter. From a sketch of its Bode plot in Fig. 12.84b, we see that at the notch frequency, fn, the transfer function gain is zero, while at frequencies above and below fn the gain is unity. Let us design a notch filter to remove an annoying 60-Hz hum

Verified Answer:
Figure 12.84c shows a block diagram for the filter...

A fast growing field within electrical engineering is mixed-mode circuitry, which combines digital and analog networks to create a larger system. A key component in these systems is the analog-to-digital converter, or ADC. It “measures” an analog voltage and converts it to a digital representation.

Verified Answer:
Assuming the ADC has infinite input resistance, we...