Shigley’s Mechanical Engineering - Solutions Manual 8th. Edition by Richard Budynas, Keith Nisbett | 9780073312606 | 0073312606 | Holooly

Mechanical Engineering

Shigley’s Mechanical Engineering - Solutions Manual

647 SOLVED PROBLEMS

Question: 11.20

The expression F^a L = constant can be written using x = L/L10 , and it can be expressed as F^a x = K or log F = (1/a) log K − (1/a) log x . This is a straight line on a log-log plot, and it is the basis of Fig. 11–5. For the geometric insight provided, produce Fig. 11–5 to scale using Ex. 11–3, ...

Verified Answer:

While we made some use of the log F-log x plot in ...

Question: 11.19

The same 02-30 angular-contact ball bearing as in Prob. 11–18 is to be subjected to a two-step loading cycle of 4 min with a loading of 18 kN, and one of 6 min with a loading of 30 kN. This cycle is to be repeated until failure. Estimate the total life in revolutions, hours, and loading cycles. ...

Verified Answer:

Total life in revolutions Let:

l

= ...

Question: 11.18

Estimate the remaining life in revolutions of an 02-30 mm angular-contact ball bearing already subjected to 200 000 revolutions with a radial load of 18 kN, if it is now to be subjected to a change in load to 30 kN. ...

Verified Answer:

Express Eq. (11-1) as

F L^{1/a}={\mathrm{co...

Question: 11.17

Different bearing metallurgy affects bearing life. A manufacturer reports that a particular heat treatment increases bearing life at least threefold. A bearing identical to that of Prob. 11–15 except for the heat treatment, loaded to 18 kN and run at 2000 rev/min, revealed an L10 life of 360 h and ...

Verified Answer:

The horizontal separation of the R = 0.90 loci in ...

Question: 11.16

A 16-tooth pinion drives the double-reduction spur-gear train in the figure. All gears have 25° pressure angles. The pinion rotates ccw at 1200 rev/min and transmits power to the gear train. The shaft has not yet been designed, but the free bodies have been generated. The shaft speeds are 1200 rev ...

Verified Answer:

This problem is rich in useful variations. Here is...

Question: 11.15

In bearings tested at 2000 rev/min with a steady radial load of 18 kN, a set of bearings showed an L10 life of 115 h and an L80 life of 600 h. The basic load rating of this bearing is 39.6 kN. Estimate the Weibull shape factor b and the characteristic life θ for a two-parameter model. This ...

Verified Answer:

Hoover Ball-bearing Division uses the same 2-param...

Question: 11.14

The worm shaft shown in part a of the figure transmits 1.35 hp at 600 rev/min. A static force analysis gave the results shown in part b of the figure. Bearing A is to be an angular-contact ball bearing mounted to take the 555-lbf thrust load. The bearing at B is to take only the radial load, so a ...

Verified Answer:

Shafts subjected to thrust can be constrained by b...

Question: 11.13

A gear-reduction unit uses the countershaft depicted in the figure. Find the two bearing reactions. The bearings are to be angular-contact ball bearings, having a desired life of 40 kh when used at 200 rev/min. Use 1.2 for the application factor and a reliability goal for the bearing pair of 0.95. ...

Verified Answer:

\begin{array}{l}{{R=\sqrt{0.95}=0.975}}\\ {...

Question: 11.12

The bearing lubricant (513 SUS at 100°F) operating point is 135°F. A countershaft is supported by two tapered roller bearings using an indirect mounting. The radial bearing loads are 560 lbf for the left-hand bearing and 1095 for the right-hand bearing. The shaft rotates at 400 rev/min and is to ...

Verified Answer:

Given:

\begin{array}{l}{{F_{r A}=560\,{\mat...

Question: 11.11

The figure is a schematic drawing of a countershaft that supports two V-belt pulleys. The countershaft runs at 1200 rev/min and the bearings are to have a life of 60 kh at a combined reliability of 0.999. The belt tension on the loose side of pulley A is 15 percent of the tension on the tight side. ...

Verified Answer:

The reliability of the individual bearings is [lat...

Loading...