Question 10.6: A vessel flange uses 16 -2-in. diameter bolts. Flange stress...

Structural Analysis and Design of Process Equipment

A vessel flange uses 16 -2-in. diameter bolts. Flange stress calculations indicate that a flange thickness of t = 4.5 in. is adequate. The bolt circle diameter is C = 22.5 in. Will secondary bending stresses be developed?

The "Step-by-Step Explanation" refers to a detailed and sequential breakdown of the solution or reasoning behind the answer. This comprehensive explanation walks through each step of the answer, offering you clarity and understanding.
Our explanations are based on the best information we have, but they may not always be right or fit every situation.

The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

This Question has been Answered.

Already have an account?

Related Answered Questions

Question: 10.14

A spherically dished head is to be bolted to the welding neck flange described in Example 10.9. The dished head is to be attached at the upper inside corner with the outside surface even with the ring’s outside (see Fig. 10.23 ). What is the minimum required thickness of the flange ring when the ...

Verified Answer:

From the geometry of Example 10.9, A = 26.5; ...

Question: 10.13

A welding-neck flange with the same geometry as that in Example 10.9 except for the thickness is used with a full-face gasket. The design pressure is 320 psi and the “soft” gasket is vegetable fiber with m = 1.75 and y = 1100. What is the minimum required thickness? ...

Verified Answer:

1 . Determine the lever arms of the inner and oute...

Question: 10.10

What is the minimum required thickness of a ring flange with the same design data as given in Example 10.9? The inside diameter has been increased to fit over the outside of the shell to where B = 12.75 in. The bolt loadings and bolt size are the same as in Example 10.9. A sample calculation sheet ...

Verified Answer:

1 . Calculate total flange moment for design condi...

Question: 10.9

What is the minimum required thickness of a welding neck flange as shown in Fig. 10.14a with the following design data? (Note: These data are the same as those used for the blind flange in Example 10.8. In Fig. 10.15 is a sample calculation of a welding neck flange. Design pressure, p, = 2,500 psi. ...

Verified Answer:

1 . Allowable bolt stress at design and seating te...

Question: 10.4

Determine the minimum corner radius to make Example 10.1 acceptable (valid) to be used. ...

Verified Answer:

The cylindrical shell thickness

t_{s}[/late...

Question: 10.12

With the reverse flange given in Example 10.11, what is the minimum required thickness based on an allowable flange stress of 17,500 psi ? ...

Verified Answer:

The tangential flange stress at the flange bore of...

Question: 10.11

A reverse flange is joined to a regular ring-type joint flange to form a reducing connection. The total bolt-up moment is controlling and equal to M0 = 2,613,000. The flange bore B´= 13.25 in.; the outside diameter A = 26.5 in.; and the flange thickness t = 5 in. What is the tangential flange ...

Verified Answer:

The tangential flange stress

S_{T}

...

Question: 10.8

Considering the pressure vessel described in Example 10.5, the vessel is to have one end closed by a blind flange. What is the minimum required thickness of the blind flange? Design data are the following: Design pressure p = 2500 psi. Design temperature = 250°F. Flange material is SA-105. ...

Verified Answer:

Following the information calculated in Example 10...

Question: 10.7

Suppose a vessel requires 24-2 ½-in. diameter bolts on a flange that is 5.5 in. thick. What is the maximum bolt circle that will not cause secondary bending stresses? The minimum bolt spacing for 2 ½-in. diameter bolts is 5 ¼ in. ...

Verified Answer:

Maximum spacing is

(2 d+t)=\left(2 \times 2...

Question: 10.5

A vessel has the following design data: design pressure p = 2500 psi; design temperature = 250°F; a spiral-wound metal, fiber-filled stainless steel gasket with an inside diameter of 13.75 in. and width N = 1.0 in. The gasket factors are m = 3.0 and y = 10,000. Bolts are SA-325 Grade 1 with ...

Verified Answer:

Determine the effective gasket seating width as fo...