Holooly Plus Logo
Holooly Plus Logo

Question 6.17: Based on the results from Probs. 6.15 and 6.16, what zones o...

Based on the results from Probs. 6.15 and 6.16, what zones of soil would be most likely to liquefy?

The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

Per Fig. 6.16, the standard penetration test data indicate that there are two zones of liquefaction from about 1.2 to 6.7 m and from 12.7 to 13.7 m below ground surface. Per Fig. 6.16, the laboratory cyclic strength tests indicate that the soil has a factor of safety against liquefaction in excess of 1.0.

6.16

Related Answered Questions

Question: 6.18

Figure 6.11 presents “before improvement” and “after improvement” standard penetration resistance profiles at a warehouse site. Assume a level-ground site with the ground-water table at a depth of 0.5 m below ground surface, the soil type is a silty sand with an average of 15 percent fines, the ...

Verified Answer:

See App. E for the solution and Fig. 6.17 for a pl...
Question: 6.15

Figure 6.15 shows the subsoil profile at a sewage disposal site in Niigata. Assume a level-ground site with the groundwater table at a depth of 0.4 m below ground surface, the medium to coarse sand has less than 5 percent fines, the total unit weight γt of the soil above the groundwater table is ...

Verified Answer:

See App. E for the solution and Fig. 6.16 for a pl...
Question: 6.16

In Fig. 6.15, assume the cyclic resistance ratio (labeled cyclic strength in Fig. 6.15) for the soil was determined by modeling the earthquake conditions in the laboratory (i.e., the amplitude and number of cycles of the sinusoidal load are equivalent to amax = 0.16g and magnitude = 7.5). Using ...

Verified Answer:

See App. E for the solution and Fig. 6.16 for a pl...
Question: 6.14

Based on the results from Probs. 6.12 and 6.13, what zones of soil will liquefy during the earthquake? ...

Verified Answer:

Per Fig. 6.14, the standard penetration test data ...
Question: 6.12

Figure 6.13 shows the subsoil profile at Kawagishi-cho in Niigata. Assume a level-ground site with the groundwater table at a depth of 1.5 m below ground surface; the medium sand and medium-fine sand have less than 5 percent fines; the total unit weight γt of the soil above the groundwater table is ...

Verified Answer:

See App. E for the solution and Fig. 6.14 for a pl...
Question: 6.13

In Fig. 6.13, assume the cyclic resistance ratio (labeled cyclic strength in Fig. 6.13) for the soil was determined by modeling the earthquake conditions in the laboratory (i.e., the amplitude and number of cycles of the sinusoidal load are equivalent to amax = 0.16g and magnitude = 7.5). ...

Verified Answer:

See App. E for the solution and Fig. 6.14 for a pl...
Question: 6.11

Use the data from the example problem in Sec. 6.4.5, but assume that the soil type is noncemented loess (i.e., soil type 7, see Fig. 6.12). Calculate the factor of safety against liquefaction. ...

Verified Answer:

CSR =0.65 r_{d} \frac{\sigma_{v 0}}{\sigma_...
Question: 6.10

Use the data from the example problem in Sec. 6.4.5, but assume that the soil type is eolian sand (i.e., soil type 4, see Fig. 6.12). Calculate the factor of safety against liquefaction. ...

Verified Answer:

CSR =0.65 r_{d} \frac{\sigma_{v 0}}{\sigma_...
Question: 6.9

Use the data from the example problem in Sec. 6.4.5, but assume that the soil type is gravelly sand (i.e., soil type 3, see Fig. 6.12) and at a depth of 3 m, qc1 = 14 MPa. Calculate the factor of safety against liquefaction. ...

Verified Answer:

CSR =0.65 r_{d} \frac{\sigma_{v 0}}{\sigma_...
Question: 6.8

Use the data from the example problem in Sec. 6.4.5, but assume that the soil type is silty gravel (i.e., soil type 2, see Fig. 6.12) and at a depth of 3 m, qc1 = 7.5 MPa. Calculate the factor of safety against liquefaction. ...

Verified Answer:

CSR =0.65 r_{d} \frac{\sigma_{v 0}}{\sigma_...