Holooly Plus Logo
Holooly Plus Logo

Question 4.9: Determine the drain-to-source voltage in the circuit of Figu...

Determine the drain-to-source voltage in the circuit of Figure 4–32 . The MOSFET data sheet gives I_{DSS} = 12 mA.

4.32
The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

Since I_{D} = I_{DSS} = 12 mA, the drain-to-source voltage is

V_{DS} = V_{DD}  –  I_{DSS}R_{D} = 18 V – (12 mA)(560 Ω) = 11.28 V

Related Answered Questions

Question: 4.14

A certain analog switch similar to the one shown in Figure 4–55 uses an n-channel MOSFET with VGS(th) = 2 V. A voltage of +5 V is applied at the gate to turn the switch on. Determine the maximum peak-to-peak input signal that can be applied, assuming no voltage drop across the switch. ...

Verified Answer:

The difference between the gate voltage and the ne...
Question: 4.12

Determine the minimum and maximum voltage gain of the amplifier in Figure 4–46 (a) based on the data sheet information in Figure 4–46 (b). ...

Verified Answer:

On the data sheet, g_{m} is shown a...
Question: 4.11

(a) What is the dc drain voltage and the ac output voltage of the amplifier in Figure 4–43? The gm is 1500 mS, ID is 2.0 mA, and VGS(off) is 3 V. (b) What is the input resistance seen by the signal source? ...

Verified Answer:

(a) First, find the dc drain voltage. V_{D}...
Question: 4.13

Determine the drain current, ID , and the source voltage, VS , of Q1 for the CD amplifier with current-source bias shown in Figure 4–48 (a). Assume the FETs are matched and each has a transconductance curve as shown in Figure 4–48 (b). ...

Verified Answer:

On the transconductance curve draw a line represen...
Question: 4.8

Figure 4–21 shows a current-source biasing circuit. What is ID ? ...

Verified Answer:

You should recognize emitter bias for the bipolar ...
Question: 4.7

Assume you are troubleshooting the JFET shown in Figure 4–18 . You do not know the transconductance of the transistor, but you need to fi nd out if the circuit is working properly. (a) Estimate the expected VG and VS . (b) Assume you measured the source voltage and found it was +5.4 V. Is the ...

Verified Answer:

(a) Start with V_{G} because this v...
Question: 4.6

The JFET shown in the circuit of Figure 4–15(a) has the transconductance curve shown in Figure 4–15(b). From the transconductance curve, determine VS and ID. Using this result, determine the value of VDS . ...

Verified Answer:

Plot the line representing a 2.0 kΩ resistor by se...
Question: 4.5

A 2N5457 general-purpose JFET has the following specifications: IDSS(min) = 1 mA, IDSS(max) = 5 mA, VGS(off)(min) = -0.5 V, VGS(off)(max) = -6 V. Select a self-bias resistor for this JFET ...

Verified Answer:

Typical of small-signal JFETs, the range of [latex...
Question: 4.4

Find VDS and VGS in Figure 4–12 . For the particular JFET in this circuit, the internal parameter values such as g m , VGS(off) , and IDSS are such that a drain current ( ID ) of approximately 5.0 mA is produced. Another JFET, even of the same type, may not produce the same results when connected ...

Verified Answer:

V_{S} = I_{D} R_{S} = (5.0 mA)(220 ...
Question: 4.3

The data sheet for an n-channel JFET shows a maximum IGSS of -0.1 nA at 25°C for VGS = -30 V and a maximum IGSS of -100 nA at 150°C for VGS = -30 V. Determine the minimum input resistance at 25°C. ...

Verified Answer:

R_{IN} = \left|\frac{V_{GS} }{I_{GSS} } \ri...