Question 11.14: For Prob. 11.13, is the dowdrag load a considerable amount w...

Geotechnical Earthquake Engineering

For Prob. 11.13, is the dowdrag load a considerable amount when compared to the increase in allowable bearing pressure for seismic loading conditions?

The "Step-by-Step Explanation" refers to a detailed and sequential breakdown of the solution or reasoning behind the answer. This comprehensive explanation walks through each step of the answer, offering you clarity and understanding.
Our explanations are based on the best information we have, but they may not always be right or fit every situation.

The blue check mark means that this solution has been answered and checked by an expert. This guarantees that the final answer is accurate.
Learn more on how we answer questions.

This Question has been Answered.

Already have an account?

Related Answered Questions

Question: 11.13

In Fig. 11.21, assume at Boring B-25 that the uppermost soil layer (silt, silty sand, and peat layer) extends from elevation -2 to -5 m and the light gray silty sand layer extends from elevation -5 to -8 m. It is anticipated that the site will be subjected to significant earthquake shaking and that ...

Verified Answer:

Calculate the downdrag load for each layer. For th...

Question: 11.12

A site consists of two sand layers. The upper sand layer is from ground surface to a depth of 8 m and is in a loose state with friction angle Φ =30°, k = 0.5, and total unit weight γt = 17 kN/m³. The underlying sand layer is much denser with friction angle Φ = 37.5°, k = 1.2, and total unit weight ...

Verified Answer:

Since there is no groundwater table, assume pore w...

Question: 11.11

Consider the same situation as Prob. 11.10, except that there is a 2 by 2 pier group. The piers are spaced 3 pier diameters (centerline to centerline). Determine the downdrag load on the pier group. ...

Verified Answer:

Since there are 4 piers in the 2 by 2 group and as...

Question: 11.10

Assume a site consists of an end-bearing pier founded on solid rock. The diameter of the pier is 3 ft and a 40 ft long zone of the pier is embedded in soft clay that is expected to settle during the earthquake. Assuming the clay has an undrained shear strength su of 500 psf, calculate the downdrag ...

Verified Answer:

Using a total stress analysis, therefore

s_...

Question: 11.6

The subsoil conditions at a site are as shown in Fig. 8.13. Predrilled cast-in-place concrete piles that have a diameter of 1 ft will be installed to a depth of 50 ft. For pile adhesion and end bearing, use an average undrained shear strength su = 0.6 kg/cm² (1200 psf). Ignoring the soil adhesion ...

Verified Answer:

Based on Fig. 11.15, use

c_{A} / c=0.67[/la...

Question: 11.5

A site has the subsoil profile as shown in Fig. 11.21 and a bridge foundation consisting of piers will be installed at the location of B-25. The piers will be embedded 3 m into the sandstone. For the sediments above the sandstone, use an average buoyant unit weight γb = 9.2 kN/m³. For the sandstone ...

Verified Answer:

Using Fig. 11.22 to obtain the bearing capacity fa...

Question: 11.2

Solve the example problem in Sec. 11.5.4, but assume that the seismic zone = 1. Compare the results with the solution to the example problem in Sec. 11.5.4. ...

Verified Answer:

Use the following data: soil profile type = [latex...

Question: 11.EP.1

Assume a pile having a diameter of 0.3 m and a length of 6 m will be driven into a nonplastic silty sand deposit having shear strength properties of c = 0 and Φ’ = 30°. Assume that the location of the groundwater table is located 3 m below the ground surface, the total unit weight above the ...

Verified Answer:

The vertical effective stress

\sigma _{v}^{...

Question: 11.15

Use the data from Prob. 11.13. The structural engineer has developed a preliminary bridge design consisting of a simply supported bridge deck. Because of high earthquake-induced lateral loads and the simply supported condition, the deflection of the piers must be minimized. Thus the structural ...

Verified Answer:

Since the upper two soil layers will liquefy durin...

Question: 11.9

For Prob. 11.4, determine the downdrag load on the concrete piers due to settlement of the sand during the earthquake. For the loose sand layer, the friction angle Φ = 30°, total unit weight γt = 17 kN/m³, and use the equation k0 = 1 – sin Φ’. The groundwater table is well below the bottom of the ...

Verified Answer:

From Prob. 11.3, the thickness of the loose sand l...